Products

Need a Document?

Sign up to view our downloads library containing our latest brochures and technical documents.

UK Ladder Regulations: What Employers Need to Know

November 5, 2026

Ladders are among the most widely used pieces of access equipment in UK workplaces. They are also a regular factor in falls from height, which accounted for more than a quarter of worker fatalities in Great Britain in 2024/25.

There is no single piece of “ladder law” in the UK. Instead, ladder use is governed by the Work at Height Regulations 2005, supported by HSE guidance and product standards.

While not intended as a substitute for indepedant health and safety advice, this guide explains what those rules mean in practice for employers, from deciding whether a ladder is appropriate to inspecting and recording ladders on site.

Are Ladders Banned in UK Workplaces?

No. It is a common misconception that health and safety law bans ladders. Under the Work at Height Regulations 2005, an employer can select a ladder where a risk assessment shows that more suitable work equipment isn’t justified because the task is low risk and either:

  • the work is of short duration
  • there are existing features on site that cannot be altered

Schedule 6 of the Regulations sets out specific requirements for ladders, covering stability, positioning and securing. Employers must also follow the wider hierarchy for work at height. That means avoiding it where possible, then using equipment that prevents falls before relying on measures that reduce the consequences of a fall. Metreel’s overview of the Work at Height Regulations 2005 covers these duties in more detail.

HSE Guidance on Ladder Safety

HSE’s guidance on the safe use of ladders and stepladders (INDG455) sets out the practical standards inspectors expect to see. The key points for leaning ladders and stepladders are:

  • Short duration: HSE guidance has long used 30 minutes in one position as a rule of thumb for short-duration ladder work
  • Light work only: ladders aren’t suitable for strenuous or heavy tasks or for carrying heavy or awkward items
  • Three points of contact: keep two hands and one foot (or two feet and one hand) on the ladder when climbing and wherever possible at the working position
  • Correct angle: set leaning ladders at 75 degrees using the 1 in 4 rule, which means one unit out for every four units up
  • Top rungs: don’t work off the top three rungs of a leaning ladder
  • Landing points: where a ladder is used to reach another level, it should extend at least 1 metre above the landing point
  • Stable base: never stand a ladder on movable objects such as pallets, bricks or boxes
  • Strong resting point: don’t rest a ladder against weak upper surfaces such as glazing or plastic guttering

Ladders should be tied or otherwise secured wherever possible. Where tying isn’t practical, an effective stability device or footing by a second person may be needed, depending on the risk assessment.

Choosing the Right Ladder: BS EN 131

Since 2018, new portable ladders sold in the UK have been made to a revised BS EN 131 standard. It replaced the older British Standards BS 2037 and BS 1129 and the classes that went with them. Ladders are now split into two categories:

  • EN 131 Professional: for use at work, including trade and industrial settings
  • EN 131 Non-Professional: for domestic use only

Both categories carry a maximum load of 150kg. The difference lies in durability testing, with Professional ladders tested to a significantly higher number of cycles. Non-Professional ladders should never be used for work.

The standard isn’t retrospective, so there is no immediate requirement to replace ladders built to older standards if they remain in good condition. When ladders are bought for workplace use, they should be specified as EN 131 Professional. Check the label on the stile to confirm the classification before a ladder is put into service.

Ladder Inspection Requirements

ladder inspection requirements

Ladders count as work equipment under PUWER 1998. Employers must therefore keep them in a safe condition and make sure they are inspected. In practice, that means three layers of checks.

Pre-Use Checks

The user should check the ladder before each use, at the start of a shift and whenever something may have changed, such as after it has been dropped or moved from a dirty area. Pre-use checks should cover:

  • stiles for bends, splits, dents or corrosion
  • feet for wear, damage or missing pads
  • rungs and steps for damage, looseness or contamination
  • locking bars, hinges and catches on stepladders and combination ladders
  • the platform and any stability devices
  • labels and markings being present and readable

Worn or missing feet are a frequent cause of ladders slipping, so they deserve particular attention.

Detailed Visual Inspections

Alongside pre-use checks, ladders need regular detailed visual inspections by a competent person. The frequency depends on how often the ladder is used and the conditions it is used in, with manufacturer instructions as a starting point. Many organisations use a numbered tag system showing when each ladder was last inspected and when the next inspection is due.

Records and Defective Ladders

Keep a record of each detailed inspection. Any ladder that fails an inspection should be taken out of use straight away, labelled clearly and either repaired in line with the manufacturer’s instructions or replaced. Damaged ladders left in a store can easily end up back in use.

Fixed Ladders

The guidance above applies to portable ladders. Permanently fixed access ladders on roofs, plant platforms and buildings are designed to separate standards covering rung spacing, landings and when collective fall protection such as a cage or a fall arrest system is required.

Metreel’s guide on when a ladder needs a cage explains those requirements. Its range of vertical access ladders includes systems with integrated fall protection for regular access to high-level areas.

When a Ladder Isn’t the Right Choice

If the risk assessment doesn’t support a ladder, there are several safer alternatives:

  • podium steps for low-level work that lasts longer than a few minutes
  • mobile access towers for longer tasks needing a stable working platform
  • mobile elevating work platforms for higher or harder-to-reach areas
  • permanent walkways, platforms or fixed ladders for repeat access to plant and roofs

Where people need to work close to an exposed edge on a regular basis, a fall restraint system can stop them reaching the point where a fall could occur.

Ladder Safety Checklist for Employers

Use the checklist below to review how ladders are managed on site:

  • a risk assessment confirms a ladder is justified for each task
  • ladders used for work are rated EN 131 Professional
  • users are trained and competent in safe ladder use
  • pre-use checks are carried out before every use
  • detailed visual inspections are completed and recorded at set intervals
  • defective ladders are removed from use and clearly labelled
  • ladders are stored securely to prevent damage and unauthorised use

Need Safer Permanent Access?

Metreel designs and installs vertical access ladders, fall arrest and fall restraint systems for industrial and commercial buildings across the UK. To discuss access to roofs, plant or high-level equipment, call us on 0115 932 7010 or contact our team.